結構: 本型干燥箱的外殼由薄鋼板成,外表面復漆,外殼與內膽之間用硅酸鋁纖維充填,形成可靠的保溫層。加熱器兩組分別裝在工作室底部,一組加熱器單*個開關管理電源通斷,101A型裝有鼓風,202B型無鼓風。 使用和注意: 1、本型烘箱應在室內工作,并安裝平穩。 2、電源輸入應裝置的前級通斷開關,并接妥良好地線。 3、必須檢查電源、電壓、電源接線無誤后,方可通電使用。 4、在新購使用或擱置較久再用時,應先用低溫烘烤80-100℃二小時后再開始升高溫度,以利潮氣外泄,增強絕緣性能和延長瓷件壽命。 5、儀表控溫的熱敏元件探頭應從左側線路的測溫孔中插入工作室內,不得從箱頂氣閥中心孔插入,以免影響使用。 6、本干燥箱初次使用時,應請勤加以觀察,避免過熱烘壞工件,造成損失。 7、使用如感到熱慣稍大時,可關閉一組加熱器以降低發熱功率,防止慣性過大造成超溫。 8、取入烘烤物件:請勿撞擊伸入工作室的控溫器部份,防止損壞控溫器導致失靈。 9、本箱切忌烘烤易爆,易燃及揮發性的物品,以防爆炸。 10、如遇故障,請專業電工檢修。 11、出廠時,工作室的擱板二塊,說明書及合格證各一份。 | 技術參數: | 型號101A | 電壓(V) | 功率KW | 工作溫度 范圍(℃) | 控溫 靈敏度℃ | 電機功率W | 工作室尺寸 MM | 外形尺寸 MM | 深×寬×高 | 深×寬×高 | —0 | 220 | 1.4 | 20-200 | ±5 | 40 | 250×300×300 | 350×660×663 | —1 | 220 | 3 | 20-300 | ±5 | 40 | 350×450×450 | 500×810×813 | —2 | 220 | 3.6 | 20-300 | ±5 | 40 | 450×550×550 | 600×910×913 | —3 | 220 | 4.6 | 20-300 | ±5 | 40 | 500×600×750 | 650×960×1113 | —4 | 3×380 | 9 | 20-300 | ±5 | 180 | 800×800×1000 | 1000×1170×1580 | —5 | 3×380 | 12 | 20-300 | ±5 | 370 | 1000×1000×1000 | 1200×1370×1580 | —6 | 3×380 | 15 | 20-300 | ±5 | 750 | 1000×1200×1200 | 1200×1570×1780 | —7 | 3×380 | 18 | 20-300 | ±5 | 750 | 1000×1200×1500 | 1200×1600×2100 | —8 | 3×380 | 21 | 20-300 | ±5 | 750 | 1200×1500×1500 | 1400×1900×2100 |
|
Product details: Structure: This type of dryer shell is composed of a thin steel plate, the outer surface of complex paint, between the shell and the liner is made of aluminum silicate fiber filling, forming a reliable insulation layer. Heater two are respectively arranged on the bottom of group studio, a group of heater a single switch management power on-off, type 101A with 202B type blast, blast. Use and pay attention: In 1, the oven should work inside, and the installation of stationary. In 2, a power input device for front on-off switch, and connected well good ground wire. 3, must check the power, voltage, power supply wiring correct, Party Ketong electricity use. In 4, the new purchase or use a long use, should first be baked at a low temperature of 80-100 ℃for two hours after the start of elevated temperature, in order to tidal leakage, enhanced insulation properties and extend the life of porcelain pieces. 5 thermistors, temperature control instrumentation probe from the left line temperature measuring hole is inserted in the studio, not from the tank top valve is inserted into the central hole, so as not to affect the use. In 6, the drying box when first used, should be invited to observe the ground, to avoid overheating drying bad work, resulting in the loss of. 7, the use of such as are thermal inertial slightly larger, can be closed by a group of heaters in order to reduce the heating power, prevent inertia caused by excessive temperature. In 8, a baking object : do not crash into the studio thermostat parts, prevent damage leading to failure of temperature control device. In 9, the box by baking and explosive, flammable and volatile items, to prevent an explosion. 10, in case of failure, please professional electrician maintenance. 11, the factory, the studio shelf two, specification and qualification certificate copies. Technical parameters: Model 101A voltage ( V ) power KW working temperature ( c ) range of temperature control Sensitivity C motor power W studio size MM dimensions MM Deep x width x height depth width x height - 2201.4 20-200± 540250 x 300 x 300350 x 660 x 663 - 12203 20-300± 540350 x 450 x 450500 x 810 x 813 - 22203.6 20-300± 540450 x 550 x 550600 x 910 x 913 - 32204.6 20-300± 540500 x 600 x 750650 x 960 x 1113 - 43 ×3809 20-300± 5180800 x 800 x 10001000 x 1170 x 1580 - 53 ×38012 20-300± 53701000 x 1000 x 10001200 x 1370 x 1580 - 63 ×38015 20-300± 57501000 x 1200 x 12001200 x 1570 x 1780 - 73 ×38018 20-300± 57501000 x 1200 x 15001200 x 1600 x 2100 - 83 ×38021 20-300± 57501200 x 1500 x 15001400 x 1900 x 2100 |