 |
上海豫東電子科技有限公司
主營產品： 惡臭檢測儀 應急檢測箱 水質安全檢測箱 水質檢測管 紅外測溫儀 紅外熱像儀 |
會員1.png)
|
上海豫東電子科技有限公司
主營產品： 惡臭檢測儀 應急檢測箱 水質安全檢測箱 水質檢測管 紅外測溫儀 紅外熱像儀 |
| 參考價 | 面議 |
聯系方式：張小姐查看聯系方式
更新時間：2017-09-22 06:37:35瀏覽次數：1847
聯系我們時請說明是制藥網上看到的信息，謝謝!
PM 2.5空氣監測用濾膜PTFE濾膜按EPA PM 2.5方法的40CFRPart 50的要求下生產出來的，生產商必須按照以下列出的測試來做。任何生產，銷售或提供銷售專門用于PM2.5 參照方法的濾膜商家，必須證明每批售出的濾膜都有一定數量經過下列測試并且90%以上符合每一個測試項目：松散、表面顆粒污染，PM 2.5采樣器空氣監測用濾膜
PM 2.5采樣器空氣監測用濾膜
PTFE濾膜按EPA PM 2.5方法的40CFR Part 50的要求下生產出來的，生產商必須按照以下列出的測試來做。
任何生產，銷售或提供銷售專門用于PM2.5 參照方法的濾膜商家，必須證明每批售出的濾膜都有一定數量經過下列測試并且90%以上符合每一個測試項目：
任何生產，銷售或提供銷售專門用于PM2.5參照方法的濾膜商家，必須證明每批受、售出的濾膜都至少有50個經過下列測試并且90%以上符合每一個測試項目：
濾膜類型、濾膜直徑、濾膜厚度、濾膜孔徑、支撐環的寬度、支撐環的厚度（總的）、zui高壓力點（清潔空氣）、zui高濕氣點、收集率、堿性。
特殊要求
這些包括XRF微量金屬分析和肉眼缺陷檢查，例如：小孔、支撐環分離、渣滓或閃紋、松動、變色、不均勻?yàn)V膜或其他明顯的濾膜缺陷。
據此申明，每批生產并銷售的于PM2.5 參照方法的濾膜，符合EPA接受標準。
| 屬性 | 測試方法 | 測量單位 | 值 | 范圍 |
| 濾膜材質 | n/a | n/a | PTFE | - |
| 濾膜厚度 | μm | μm | 40 | ±10 |
| 濾膜直徑 | mm | 模具 | 46.2 | 2.5 |
| 濾膜孔徑 | ASTM F 316-94 | μm | 2 | zui大 |
| 支撐環材質 | n/a | n/a | 聚丙烯 | - |
| 支撐環厚度 | mm | mm | 0.38 | ±0.04 |
| 支撐環寬度 | mm | 模具 | 3.68 | ±0.00-0.51 |
| 顆粒保留率（0.3μm） | ASTM D 2986-91 | % | 99.7 | zui小 |
| Pressure Drop（0.3μm）@16.67L/min | ASTM D 2986-91 | cm H2O | 30 | zui大 |
| 堿性 | Section 2.12 EPA/600/R-94/038b | μeq/g of filter | <25 | zui大 |
| Temperture Wt.Loss Stability | 同上 | μg | <20 | 平均 |
| Drop Test Wt.Stability | 同上 | μg | <20 | 平均 |
| Moisture Wt.Gain Stability | 同上 | μg | <10 | 平均 |
| 品名 | 規格 | 包裝 |
| PM2.5空氣監測用濾膜 | 尺寸：46.2m，帶聚丙烯支撐環和順序編的PTFE膜 | 50張/包 |
| 熒光素X光檢測的zui高痕量元素濃度 Maximum Trace Element Concentration by X-Ray Fluoresence | |||||||||||
| Ion | ng/cm2 | Ion | ng/cm2 | Ion | ng/cm2 | Ion | ng/cm2 | Ion | ng/cm2 | Ion | ng/cm2 |
| Al | 94.4 | Sc | 7.2 | Ni | 3 | Br | 2 | Pd | 9.6 | Cs | 25 |
| Si | 32.8 | Ti | 13.8 | Cu | 2.8 | Rb | 2 | Ag | 9.6 | Ba | 32.2 |
| P | 22.6 | V | 4.8 | Zn | 2.2 | Sr | 2.2 | Cd | 10.8 | La | 87.6 |
| S | 13.4 | Cr | 2.2 | Ga | 1.8 | Y | 14.6 | Sn | 15.2 | W | 5 |
| Cl | 9.4 | Mn | 2.2 | Ge | 3 | Zr | 13.2 | Sb | 14.4 | Au | 4.4 |
| K | 5.6 | Fe | 5.8 | As | 2.8 | Mo | 11.6 | Te | 16.2 | Hg | 4.4 |
| Ca | 8.2 | Co | 4 | Se | 1.6 | Rh | 9.4 | I | 18.6 | Pb | 4.8 |
Statement of Conformance
PTFE Filters for EPA PM 2.5 Reference Method.Under the requirements of 40 CFR Part 50, Appendix L, shown below, the manufacturer must perform the following tests as listed.
Any filter manufacturer or vendor who sells or offers to sell filters specifically identified for use with this PM 2.5 reference method shall certify that the required number of filters from each lot （0.1% or 10, whichever is greater） of filters offered for sale have been tested as specified for the following tests and meet 90% of each of the design and performance specifications:
Any filter manufacturer or vendor who sells or offers to sell filters specifically identified for use with this PM 2.5 reference method shall certify that a minimum number of 50 filters from each lot of filters offered for sale have been tested as specified for the following tests and meet 90% of each of the design and performance specifications:
These include trace metal analysis by XRF and visual inspection for defects such as pinholes, support ring separation, chaff or flashing, loose material, discoloration, filter non-uniformity or any other obvious filter defect.
Whatman hereby states that every manufacturing lot that is offered for sale, and is identified for use with the PM 2.5 reference method, conforms to EPA acceptance criteria.
