粉末壓片機

一、粉末壓片機用途:

粉末壓片機噸位大、體積小適用于較大截面積的粉模壓片，或需要較大壓力的場合，配上不同形狀 的模具，可以壓出不同形狀不同尺寸的片子

the use of powder tableting machine:

The powder tableting machine has a large tonnage and a small volume. It is suitable for large-sized cross-sectional powder molding tablets, or where large pressure is required. With different shapes of molds, it is possible to press out films of different shapes and sizes.

二、粉末壓片機技術參數:

★壓力范圍：0~24噸（0~40MPa）

★活塞直徑：Φ87mm

★大活塞行程：20mm

★工作空間：94×94×180mm

★壓力穩定性：≤1MPa/5min

★重量：40公斤

★外形尺寸：280×210×530mm

Second, the powder tablet press technical parameters:

★ Pressure range: 0~24 tons (0~40MPa)

★Piston diameter: Φ87mm

★ Large piston stroke: 20mm

★Working space: 94×94×180mm

★ Pressure stability: ≤1MPa/5min

★ Weight: 40 kg

★Dimensions: 280 × 210 × 530mm

三、粉末壓片機操作規程：

★機器使用前須檢查沖模是否有缺邊、裂縫、變形等質量問題，檢查機器各裝置是否完好。

★檢查顆粒原粒是否符合要求，顆粒中的細粉含量不宜超過10%，以免影響機器使用性能及壽命。

★開車前應用手轉動帶輪或順點動按鈕試壓，確定片劑符合要求，機器運轉正常后，方可開機投入生產。

★機器設有倒車點動按鈕，壓片時產生疊片或上沖粘沖悶車及校核上沖進模情況進可使用，使用時只允許瞬時點動使機器微量反轉，否則會損壞機件。

★使用中要隨時注意機器的運轉情況，如有異常聲響，即應停機檢查，排除故障后再使用。

Third, the powder tablet press operating procedures:

★ Before using the machine, check whether the die has quality problems such as missing edge, crack, deformation, etc. Check whether the machine is in good condition.

★ Check whether the original particles of the particles meet the requirements, the fine powder content in the particles should not exceed 10%, so as not to affect the machine performance and life.

★ Before driving, apply the hａnd to rotate the pulley or click the button to test the pressure to ensure that the tablet meets the requirements. After the machine is running normally, it can be put into production.

★The machine is equipped with a reversing jog button. When the sheet is pressed, the lamination or the punching and squeezing the car and the check on the die can be used. When using, only the momentary jog is allowed to make the machine slightly reverse, otherwise it will be damaged. Machine parts.

★ Please pay attention to the operation of the machine at any time during use. If there is abnormal noise, stop the machine and use it after troubleshooting.

四、粉末壓片機注意事項：

★使用前必須先松開注油孔螺釘，壓片機才能正常工作

★定期在絲杠及柱塞泵處加潤滑油

★加壓決不允許超過機器的壓力范圍，否則會發生危險

★壓片機使用清潔的46號機油為宜，絕不可用剎車油

★加壓時感覺手動壓把有力，但壓力表無指示，應立即卸荷檢查壓力表

★新機器或較長一段時間沒有使用時，在用之前稍緊放油閥，加壓到20~25MPa時即卸荷，連續重復2~3次，即可正常使用

★大活塞不要超過行程20mm

Fourth, the powder tableting machine notes:

★The oil hole screw must be loosened before use, and the tablet press can work normally.

★ Regularly lubricate the screw and plunger pump

★Pressure must never exceed the pressure range of the machine, otherwise danger will occur

★The tablet press is made of clean No. 46 oil, never use brake oil.

★When pressure is applied, the manual pressure is strong, but the pressure gauge has no indication. It should be unloaded immediately to check the pressure gauge.

★When the new machine is not used for a long period of time, put the oil valve slightly before use, and unload it when pressurized to 20~25MPa, repeat it for 2~3 times, then it can be used normally.

★Do not exceed 20mm of large piston